[manager]
# Delay between setting GPIO and PWRKEY sequence, set in microseconds
poweron_delay = 100000

# Uncomment the following if you need to change the modem detection timeout on
# resume and/or the time during which suspend is blocked after modem boot
#[suspend]
#boot_timeout = 120
#recovery_timeout = 9

[gpio]
chips = [ "gpio0", "gpio3" ]
dtr = { chip = 0, line = 3 }
pwrkey = { chip = 0, line = 13 }
reset = { chip = 1, line = 8 }
apready = { chip = 0, line = 12 }
disable = { chip = 0, line = 8 }
status = { chip = 1, line = 6 }

[at]
uart = "/dev/ttyS3"
configure = [
# Each command has 4 possible elements:
#   * `cmd`   : the AT command itself, which will be translated to "AT+`cmd`"
#   * `subcmd`: the subcommand in case a single AT command can be used
#               to change multiple parameters, such as QCFG (optional)
#   * `value` : the commands, argument, usually used to set the value of
#               a specific parameter (optional)
#   * `expect`: the expected return value; the command is first executed
#               without any value in order to query the current state. This
#               state is then compared to the `expect` string; if they don't
#               match, the command is then executed with value `expect` in
#               order to set the parameter to the configured value (optional)
# A command can have `expect` OR `value` configured, but it shouldn't have both
# Print software version
    { cmd = "QGMR" },
# Configure audio
    { cmd = "QDAI", expect = "3,0,0,4,0,0,1,1" },
# RI signaling using physical RI pin
    { cmd = "QCFG", subcmd = "risignaltype", expect = "\"physical\"" },
# Enable VoLTE support
    { cmd = "QCFG", subcmd = "ims", expect = "1" },
# Enable APREADY for PP 1.2
    { cmd = "QCFG", subcmd = "apready", expect = "1,0,500" },
# URC configuration for PP 1.2 (APREADY pin connected):
#   * RING URC: normal pulse length
#   * Incoming SMS URC: default pulse length
#   * Other URC: default length
#   * Report URCs on all ports (serial and USB) for FOSS firmware
#   * Reporting of URCs without any delay
#   * Configure URC pin to UART Ring Indicator
    { cmd = "QCFG", subcmd = "urc/ri/ring", expect = "\"pulse\",120,1000,5000,\"off\",1" },
    { cmd = "QCFG", subcmd = "urc/ri/smsincoming", expect = "\"pulse\",120,1" },
    { cmd = "QCFG", subcmd = "urc/ri/other", expect = "\"off\",1,1" },
    { cmd = "QCFG", subcmd = "urc/delay", expect = "0" },
    { cmd = "QCFG", subcmd = "urc/cache", expect = "0" },
    { cmd = "QCFG", subcmd = "urc/ri/pin", expect = "uart_ri" },
    { cmd = "QURCCFG", subcmd = "urcport", expect = "\"all\"" },
# Allow sleeping for power saving
    { cmd = "QSCLK", value = "1" },
# GNSS configuration:
#   * Enable A-GPS data upload support (XTRA)
#   * Disable On-Demand-Positioning (ODP) mode 
#     to avoid running the GNSS system in the background, even when not enabled.
#   * Enable Dynamic Power Optimizations (DPO) mode to turn off GNSS RF radios 
#     when they are not in use.
#   * Only enable GPS and GLONASS, disable other GNSS systems.
#     A-GPS data upload doesn't work for Galileo anyway.
#   * Avoid turning on GNSS support automatically when the modem boots.
    { cmd = "QGPSXTRA", expect = "1" },
    { cmd = "QGPSCFG", subcmd = "gnssconfig", expect = "4" },
    { cmd = "QGPSCFG", subcmd = "odpcontrol", expect = "0" },
    { cmd = "QGPSCFG", subcmd = "dpoenable", expect = "1" },
    { cmd = "QGPSCFG", subcmd = "gpsnmeatype", expect = "31" },
    { cmd = "QGPSCFG", subcmd = "glonassnmeatype", expect = "7" },
    { cmd = "QGPSCFG", subcmd = "galileonmeatype", expect = "0" },
    { cmd = "QGPSCFG", subcmd = "beidounmeatype", expect = "0" },
    { cmd = "QGPSCFG", subcmd = "autogps", expect = "0" },
# Disable fast poweroff for stability
    { cmd = "QCFG", subcmd = "fast/poweroff", expect = "0" },
# Configure sleep and wake up pin levels to active low
    { cmd = "QCFG", subcmd = "sleepind/level", expect = "0" },
    { cmd = "QCFG", subcmd = "wakeupin/level", expect = "0,0" },
# Do not enter RAMDUMP mode, auto-reset instead
    { cmd = "QCFG", subcmd = "ApRstLevel", expect = "1" },
    { cmd = "QCFG", subcmd = "ModemRstLevel", expect = "1" },
]
suspend = [
]
resume = [
]
reset = [ { cmd = "CFUN", value = "1,1" } ]

[gnss]
enabled = true
url = "https://xtrapath4.izatcloud.net"
file = "xtra2.bin"